Documentation Center

Viz Mosart Administrator Guide

Version 4.1 | Published November 09, 2022 ©

AV Automation Devices Audio

Viz Mosart can connect to a variety of audio mixers from several manufacturers.

From the Audio tab, the Audio Mixer, Sound player and Loudness settings can be configured, on a per-device basis.
AV Automation handles the following audio alternatives:

Audio Mixer

images/download/attachments/95394632/audioMixer.png

  • Use Audio mixer: Enables the audio mixer functionality.

The screenshot above is a for a midi mixer. Depending on which audio mixer is selected, the menu will display different fields. All fields are described below.

Audio Mixer Types

Audio mixer

Protocol

Supported hardware

Interface

Calrec

RAP


RS-422, TCP/IP (Artemis)

DHD

DHD RM4200-D v2.02


TCP/IP

EUPHONIX

RAP


COM

LAWO RMNOPL

RemoteMNOPL

Lawo mc²

TCP/IP

LAWO ZIRKON

RAS, Lawo Zirkon subset



RS-422 or TCP/IP

MIDIMIXER

Sanford.Multimedia


MIDI

SSL

Light Broadcast Automation protocol, SSL Broadcast Automation Control Specification – v1.0


RS-422 or TCP/IP

STAGETEC

Stagetec Diamond RAS protocol, Monitora RAS


COM

STUDER_3000

Monitora + Ember, Ember 1.0

Studer OnAir 3000

RS-232 or TCP/IP

STUDER_VISTA

Ember

Studer Vista

TCP/IP

VIZENGINE

n/a

Viz Opus only

TCP/IP

WHEATSTONE

Wheatstone Mixer Automation Protocol v.1.4


TCP/IP

YAMAHA_O2

MIDI

Yamaha 01V96, DM1000, DM2000, DME64N, O2V96, LS9, CL5

MIDI

vizrt-ips

NewTek

Vizrt Group/NewTek ip series mixers. TriCaster, VMC, Viz Verdi, Viz Vectar

TCP/IP

  • Serial (Calrec, Lawo, Studer, etc.): Serial port connected to the audio mixer (when Serial radio button is selected).

  • TCP/IP: Hostname (or IP address) and port to communicate with the audio mixer (when TCP/IP radio button is selected). Note that for Calrec it is possible to configure a main and backup audio mixer by specifying two comma separated hostname values and port values.

  • Backup hostname and port (LAWO RMNOPL): Hostname (or IP address) and port to the backup audio mixer console.

  • Set user labels on console: When selected, user labels on the Lawo or Vista console are overwritten.

  • MidiCh (MIDIMIXER and YAMAHA_O2): MIDI channel assigned to the audio mixer.

  • Midi Input port (MIDIMIXER and YAMAHA_O2): System MIDI input port to communicate with the audio mixer.

  • Midi Output port (MIDIMIXER and YAMAHA_O2): System MIDI output port to communicate with the audio mixer.

  • Default fade time: Time in frames for fading open faders with the manual fade function (CTRL+F).

  • Default snapshot: Snapshot to recall when starting the automation (MIDI parameter change).

  • Audio effect server: Name for the Audio effect fader. This fader will open if effect transitions are used.

  • Send reset command on connect: Used for STUDER3000 SW 2.2, or lower. Recalls a default setup for the Mixer panel.

  • Visible audio faders: Maximum visible faders in AV Automation.

AV Automation Audio Mixer Availability Table

Serial

TCP/IP

MidiCh

Midiport

Hostname

Port

Backup
host name

Backup
Port

Faderinput
offset

Useember
protocol

Comport
audiomixer

CALREC

x

x



x

x





x

DHD


x



x

x






EUPHONIX

x










x

LAWO
RMNOPL


x



x

x

x

x




LAWO
ZIRKON

x

x



x

x





x

MIDI
MIXER



x

x








SSL

x








x


x

STAGETEC

x

x



x

x





x

STUDER
3000

x

x



x

x




x

x

STUDER
VISTA


x



x

x






VIZ
ENGINE


x



x

x






WHEAT
STONE


x



x

x






YAMAHA
O2



x

x








Vizrt
ips


x



x

x






Loudness Control

images/download/attachments/95394632/configuration_avauto-loudness.png

  • Use loudness controller: Check the box to enable loudness control.

  • Loudness controller type: JUNGER T*AP.

  • Triggers/levels: Name of triggers or loudness levels, one for each line. These will appear in a tool-tip menu in the Template editor, and must correspond to the configuration in the loudness controller(s).

  • Channels: Fixed values. For Junger T*AP there are four stereo channels per host. Connections to the audio faders are configured in A/V Setup/Edit/Audio config/Loudness channel.

  • Host:port: Hostname or IP address and optional port number for each controller.

Note: If the root node name is different than T*AP the name must be set in the AVA configuration property JungerRoot .

Sound Player

images/download/attachments/95394632/soundPlayer.png

  • Use sound player: Enables connection to the Audio Player.
    Select from either the Mosart Sound File Player or Mosart Audio Player.

  • Host: Hostname or IP address to the computer running the Audio Player.

  • Default directory: Directory for the audio files (on the Audio Player’s PC).

See Also